FV535 Alloy Sheet Plate | DIN 1.4935 | BS FV535

UNS S13500 FV535 Alloy Sheet & Plate, AMS 5615 FV535 Alloy Sheet & Plate, ASTM A693 FV535 Alloy Sheet & Plate, Werkstoff 1.4545 FV535 Alloy Sheet & Plate, FV535 Hot Rolled Sheet & Plate, FV535 Cold Rolled Sheet & Plate in India.

PM Industries manufactures, supplies, and stocks FV535 Alloy Sheet Plate in a range of thicknesses and sizes. FV535 is a high-strength martensitic stainless steel developed for elevated temperature service in gas turbines, aerospace structures, and precision engineering applications where high strength, toughness, and thermal stability must all be present simultaneously. It's a chromium-molybdenum-vanadium alloy with a composition optimized for strength retention at elevated temperature rather than for aqueous corrosion resistance, which distinguishes it from the standard austenitic and duplex corrosion-resistant grades.

FV535 Alloy Sheet & Plate Manufacturer, AMS 5615 FV535 Alloy Sheet & Plate Supplier, UNS S13500 FV535 Alloy Sheet & Plate Stockist, ASTM A693 FV535 Alloy Sheet & Plate Exporter in India.

The alloy is heat-treatable, responding to quench and temper treatment to develop the combination of tensile strength and toughness required for its intended applications. The temper condition determines where the balance sits between maximum strength and maximum toughness, and the appropriate temper for a given application is defined by the design requirement and the applicable material specification.

Elevated temperature strength retention is what drives FV535 specification in gas turbine and aerospace applications. In rotating and structural components that experience both mechanical load and elevated service temperature simultaneously, the alloy must maintain adequate yield strength and creep resistance throughout the operating temperature range. FV535's chromium-molybdenum-vanadium composition provides solid-solution and precipitation strengthening that supports that requirement across the alloy's rated service temperature range.

Heat treatment response gives fabricators control over the final mechanical property balance. Higher tempering temperatures produce better toughness with some reduction in tensile strength. Lower tempering temperatures maintain maximum strength with somewhat reduced toughness. For each specific application, the tempering condition is selected to meet the strength floor required by the design while maintaining acceptable toughness for the loading conditions and failure mode risk.

Wear resistance under mechanical contact is relevant for components where surface loading or sliding contact is part of the service condition. The hardened martensitic structure provides better surface resistance to mechanical degradation than softer austenitic grades, which makes FV535 practical for components where both structural load-bearing and surface durability are requirements.

Sheet and plate form makes FV535 accessible for fabricated structural components, formed aerospace sheet metal parts, and precision-machined structural members that require flat product as the starting material. With appropriate tooling and procedures, FV535 sheet can be cut, formed, and welded for fabricated assemblies, with heat treatment performed on the assembly or finished component to develop final mechanical properties.

Sheet and plate are available in a range of thicknesses and sizes with material certification to applicable BS, AMS, and DTD specifications. Contact PM Industries for thickness, width, condition, and pricing.

Specification FV535 Stainless Sheet & Plate | DIN 1.4935 | BS FV535

Specifications	ASME SA 240/ASTM A 240
Standard Sizes	1000 x 2000 mm, 1220 x 2440 mm, 1500 x 3000 mm, 2000 x 2000 mm, 2000 x 4000 mm
Width	10-2500mm
Length	2000mm, 2440mm, 3000mm, 5800mm, 6000mm, etc
Surface	2B, 2D, BA, NO.1, NO.4, NO.8, 8K, mirror, checkered, embossed, hairline, sand, blast, Brush, etching, etc
Thickness	0.1mm to 100 mm Thk
Hardness	Quarter Hard, Half Hard,Spring Hard, Soft, Hard
Stock available in form of	Shim Sheet, Rolls, Strip, Flats, Clad Plate, Plain Sheet, Plate, Sheet, Coils, Foils, Rolling Sheet, Rolling Plate, Flat Shim, Flat Sheet, Blank (Circle), soft annealed, sheared, annealed, tread plate,descaled, Checker Plate
Profiling	Plasma Plate Cutting
Value added services	Plasma cutting, Waterjet cutting, Laser cutting, welding, edge preparation, etc.
Test Certificates	EN 10204/3.1B, NACE MR0103, NACE MR0175
	Raw Materials Certificate
	100% Radiography Test Report
	Third Party Inspection Report, etc

Available Types of FV535 Alloy Sheet & Plate

FV535 Alloy Sheets & Plates – Equivalent Grades

Grade	AMS	ASTM	UNS	Werkstoff (DIN)	Common Name
FV535	AMS 5615	ASTM A693	S13500	1.4545	FV535 Stainless Steel

FV535 Alloy Sheet & Plate – Chemical Composition

Grade	C	Cr	Ni	Mo	Cu	Mn	Si	P	S	Fe
FV535	0.05 max	14.0 – 15.5	4.5 – 5.75	1.2 – 1.8	2.5 – 3.5	1.0 max	1.0 max	0.030 max	0.030 max	Bal

FV535 Alloy Sheets & Plates – Mechanical Properties

Grade	Condition	Tensile Strength (MPa)	Yield Strength (MPa)	Elongation (%)	Hardness (HRC)
FV535	Solution Treated & Aged	≥ 1030	≥ 860	≥ 10	≈ 32 – 38