Aluminium 6082 T6 Round Bar | UNS A96082 | DIN 3.2315

3.2315 Round Bar Stockist, Aluminium 6082 T6 Round Bar Supplier, ASTM B221 Aluminium 6082 T6 Round Bar Distributor, UNS A96082 Round Bar Manufacturer, EN AW-6082 Round Bar Exporter.

PM Industries manufactures, supplies, and stocks Aluminium 6082 T6 Round Bar. It belongs to the 6000 series aluminium-magnesium-silicon family and is one of the highest-strength alloys in that series. T6 temper means the material has been solution heat-treated and artificially aged, which gives it better mechanical properties than the annealed or T4 condition.

ASTM B221 Aluminium 6082 T6 Round Bar, 3.2315 Round Bar, UNS A96082 Round Bar, Aluminium 6082 T6 Round Bar.

6082 is often the structural grade of choice in European engineering and fabrication, in the same way 6061 T6 is commonly specified in North American markets. The two alloys are closely related in composition and performance, though 6082 typically offers slightly higher strength.

Corrosion resistance is reliable in outdoor, coastal, and moderate industrial environments. For marine hardware, outdoor frames, and exposed structural components, 6082 T6 performs well without special coatings in many service conditions. Anodizing improves surface protection further and gives the material a clean, finished appearance.

Weldability is good. Joints hold well with proper technique, though some reduction in strength at the heat-affected zone is expected, as with other heat-treatable aluminium alloys. For welded structural assemblies, this is a well-understood and manageable characteristic.

Machinability is consistent. The bar cuts, drills, and turns cleanly, making it practical for both precision components and general fabrication. Surface finish off the machine is good, which reduces secondary finishing work in many applications.

Bar is available in T6 temper across a range of diameters and surface finishes, including mill finish, polished, and anodized. Contact PM Industries for stock availability, dimensions, and pricing.

Specification Aluminium 6082 T6 Round Bar

Specification	ASTM, EN, DIN, JIS, BS, ASME, AISI
Condition	Hardened & tempered, annealed
Length	1 to 6 Meters, Custom Cut Lengths
Round Bars	Outside Diameter in the range of 4mm to 500mm above as per the customer requirement.
Bright Bars	Outside Diameter in the range of 4mm to 500mm above as per the customer requirement.
Hex Bars	18mm – 57mm (11/16″ to 2-3/4″) above as per the requirement.
Square Bars	18mm – 47mm (11/16″ to 1-3/4″) above as per the requirement.
Flat Bars	1/2” to 10” in thickness range of 2mm to 150mm
Finish	Black, Bright Polished, Rough Turned, NO.4 Finish, Matt Finish, BA Finish
Technique	Hot Rolled, Cold Rolled, Cold Drawn, Forged Round Bar, Rod
Tolerance	H8, H9, H10, H11, H12, H13, K9, K10, K11, K12 or as per clients’ requirements
Test Certificates	EN 10204/3.1B, NACE MR0103, NACE MR0175
Raw Materials Certificate	100% Radiography Test Report
Inspection	Third Party Inspection Report, etc

Available Types

Aluminium 6082 T6 Round Bar Chemical Composition

Element	% Present
Al	Balance
Si	0.70 – 1.30
Mg	0.60 – 1.20
Mn	0.40 – 1.00
Fe	0.0 – 0.50
Zn	0.0 – 0.20
Ti	0.0 – 0.10
Cu	0.0 – 0.10
Cr	0.0 – 0.25
Others (Total)	0.0 – 0.15
Other (Each)	0.0 – 0.05

Aluminium 6082-T6 Round Bar Mechanical Strength

Element	Aluminium 6082 T6
Proof Stress	290 Typical MPa
Tensile Strength	340 Typical MPa
Hardness Vickers	95 Typical HV
Elongation A	6 Min %

Aluminium 6082-T6 Round Bar Mechanical Strength

Element	Aluminium 6082 T6
Proof Stress	290 Typical MPa
Tensile Strength	340 Typical MPa
Hardness Vickers	95 Typical HV
Elongation A	6 Min %

Aluminium 6082 T6 Round Bars Equivalent

STANDARD	WERKSTOFF NR.	UNS	EN
Aluminium 6082 T6	3.2315	A96082	AW-6082

Size

US Bar		Metric		Japanese		Canadian/ASTM
Diameter (Inch)	Size of Bar	Diameter (milimeter)	size of Bar	Diameter (milimeter)	size of Bar	Diameter (milimeter2)	size of Bar
0.375	#3	5.5	5.5	10	10	200	15M
0.25	#2	5	5	6	6	100	10M
0.625	#5	7	7	16	16	500	25M
0.5	#4	6	6	13	13	300	20M
0.875	#7	9	9	22	22	1000	35M
0.75	#6	8	8	19	19	700	30M
1.125	#9	11	11	29	29	2500	55M
1	#8	10	10	25	25	1500	45M
1.375	#11	14	14	35	35
1.25	#10	12	12	32	32
1.625	#13	18	18	41	41
1.5	#12	16	16	38	38
1.875	#15	22	22	48	48
1.75	#14	20	20	44	44
2.25	#18	28	28	57	57
2	#16	25	25	51	51
		36	36
		32	32
		44	44
		40	40
		50	50

Condition

ANN	Annealed
H&T	Hardened and tempered.
PH	Precipitation hardened.

Finish

Bright drawn	BD	Slit rolled edge	SRE
Cold drawn	CD	Polished	P
Peeled and turned	P&T	Rough turned/peeled	RT
Cold finished	CF	Hot rolled pickled and annealed	HRAP
Centreless ground	CG	Hot finished	HF
Smooth turned	ST	reeled and Peeled	PR

Available Stock

Aluminium 6082 T6 Annealed Round Bar	JIS A6082 Shafting Round Bar
UNS A96082 Normalized Round Bar	Aluminium 6082 T6 Automotive Round Bar
3.2315 Quenched & Tempered Round Bar	UNS A96082 Aerospace Round Bar
ASTM B221 Aluminium 6082 T6 Solution Annealed Round Bar	3.2315 Oil & Gas Round Bar
EN AW-6082 Hardened Round Bar	ASTM B221 Aluminium 6082 T6 Marine Round Bar
ISO AlMgSi1 Bright Round Bar	EN AW-6082 Medical Grade Round Bar
BS EN 573 Polished Round Bar	ISO AlMgSi1 Hot Rolled Round Bar
JIS A6082 Mirror Finish Round Bar	BS EN 573 Cold Drawn Round Bar
Aluminium 6082 T6 Pickled & Passivated Round Bar	JIS A6082 Cold Rolled Round Bar
UNS A96082 Coated / Plated Round Bar	Aluminium 6082 T6 Forged Round Bar
3.2315 Commercial Round Bar	UNS A96082 Peeled Round Bar
ASTM B221 Aluminium 6082 T6 Precision Round Bar	3.2315 Turned Round Bar
EN AW-6082 Straight Length Round Bar	ASTM B221 Aluminium 6082 T6 Ground Round Bar
ISO AlMgSi1 Cut-to-Length Round Bar	EN AW-6082 Centreless Ground Round Bar
BS EN 573 Structural Round Bar	ISO AlMgSi1 Precision Ground Round Bar