ASTM A694 F80 Flanges | ASME B16.5 | MSS SP-44

PM Industries is a manufacturer, supplier, and stockist of ASTM A694 F80 Flanges, high-strength carbon steel forged flanges made for high-pressure transmission systems and demanding industrial service. ASTM A694 specification covers carbon and alloy steel forgings for pipe flanges, fittings, valves, and parts used in oil, gas, petrochemical, and energy systems that run under severe pressure and temperature. The F80 grade carries a minimum yield strength of 80 ksi (550 MPa), which gives strong structural integrity and good resistance to mechanical stress.

A694 F80 flanges are forged from quality carbon steel and put through controlled heat treatment and quality checks to reach high toughness, good impact resistance, and consistent mechanical properties. The minimum tensile strength runs about 90 ksi (620 MPa), with elongation of at least 18%. That combination holds up in critical piping under cyclic load, vibration, and high-pressure service. The steel also welds and machines well, which keeps fabrication, installation, and maintenance straightforward while supporting secure, leak-tight joints.

A694 F80 is available across the full range of flange types, including weld neck, slip-on, blind, socket weld, threaded, lap joint, long weld neck, spectacle blind, and orifice flanges, along with custom forged shapes. Manufacturing follows international dimensional standards such as ASME B16.5, ASME B16.47 Series A and B, MSS SP-44, and API, plus customer-specific requirements.

These flanges come in pressure classes from 150 through 2500, with raised face, ring-type joint, and flat face options. They are used in oil and gas transmission pipelines, offshore platforms, petrochemical plants, refineries, power generation facilities, LNG terminals, chemical plants, compressor stations, water treatment systems, and heavy industrial infrastructure.

Every flange is inspected and tested, with chemical analysis, tensile and hardness testing, ultrasonic and impact testing, hydrostatic testing, and dimensional checks to confirm compliance with ASTM and ASME standards. When ordering ASTM A694 F80 flanges, define the type, size, pressure class, facing, and the certification and traceability you need. PM Industries supplies A694 F80 flanges across the full size and class range, each produced under strict quality control. Contact our team for sizes, certification, and lead times on your next order.

Specification ASTM A694 F80 Flanges

Standards	ANSI/ASME B16.5, B16.48, ANSI Flanges, GOST Flanges, DIN Flanges, EN-1092, B16.47 Series A & B, ASME Flanges, EN Flanges, AWWA Flanges, BS Flanges.
JIS Standard	5K, 10 K, 16 K 20 K, 30 K, 40 K, 63 K
DIN FLANGES	DIN 2527, 2627, 2631, 2656, 2576, 2673, 2629, 2628, 2566, 2641, 2637, 2655, 2634, 2636, 2632, 2633, 2638, 2642, 2573, 2635.
Pressure Rating	Class 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
Types	Threaded, Plate, Screwed, Forged.
Supporting material	Gasket, Ring Joint, Flange Bolts
Size range	1/2" (15 NB) to 48" (1200NB) DN10~DN5000
Production technique	Forged, machined and Heat treated
Available Flange Type	Weld Neck Flanges, RTJ Flanges, Slip On Flanges, Spectacle Blind Flanges, Flanges Gaskets, Square Flanges, Standard Insert Flanges, High Hub Blinds Flanges, Flat Flanges, forged flanges, Weldo / Nipo Flanges, Jacket Insert Flanges, Tongue groove Flanges, Blind Flanges, Socket Weld Flanges, Large diameter Flanges, Long Weld Neck Flanges, Spacer Blinds, SWRF Flanges, SORF Flanges, Angle Face Rings Flanges, Spades Ring Spacers Flanges, WNRF Flanges, Screwed Flanges, Insert Flanges, flanges bolts, cf flange, Lap Joint Flanges, ASME B16.36 Orifice Flanges, Plate Flange, Expander Flanges, Ring Type Joint Flanges, Loose Flanges, Reducing Flanges, puddle flange, Threaded Flanges, blank flange, vacuum flange.
Connect Type/ Flange Face Type	Ring Type Joint (RTJ), Flat Face (FF), Tongue & Groove, Small Male-Female (SMF), Lap-Joint Face (LJF), Raised Face (RF), Large Male-Female (LMF), Small Tongue.
Custom design	As per your drawing
Test	Direct-reading Spectrograph, X-ray detector, UItrasonic flaw detector, Magnetic particle detector, Hydrostatic testing machine.
Origin	Indian / USA / Korean / West Europe / Japan
Pressure Class	PN 6 TO PN 100
Thickness	Normal Pipe Size ≤ 18
Bore Diameter	Normal Pipe ≤ 10
High Temperature	Above 200°C (400°F) For Class 150 Or Above 400°C (750°F)
Low Temperature	Above -29 Degree C (−20°F)
Coating/Surface Treatment:	Zinc Plated, Anti-rust Paint, Oil Black Paint, Yellow Transparent, Cold and Hot Dip Galvanized.
European/African/Russian Standard Flanges	Available
Gaskets Types	Full Face, Metallic Ring, Flat Ring Gasket
Marking Standard	Name of Manufacturer
	Schedule
	Type of Flange Facing
	Pressure Class
	Nominal Pipe Size, etc
Test Certificates	EN 10204/3.1B, NACE MR0103, NACE MR0175
	Raw Materials Certificate
	100% Radiography Test Report
	Third Party Inspection Report, etc

Flange Type Available

ASME/ANSI B16.5 F80 Flanges Dimensions Class-150

Nominal Pipe Size NPS (inches)	Class 150
	Diameter of Flange (inches)	No. of Bolts	Diameter of Bolts (inches)	Diameter of Bolt Holes (inches)	Bolt Circle (inches)
1/4	3-3/8	4	1/2	0.62	2-1/4
1/2	3-1/2	4	1/2	0.62	2-3/8
3/4	3-7/8	4	1/2	0.62	2-3/4
1	4-1/4	4	1/2	0.62	3-1/8
1-1/4	4-5/8	4	1/2	0.62	3-1/2
1-1/2	5	4	1/2	0.62	3-7/8
2	6	4	5/8	0.75	4-3/4
2-1/2	7	4	5/8	0.75	5-1/2
3	7-1/2	4	5/8	0.75	6
3-1/2	8-1/2	8	5/8	0.75	7
4	9	8	5/8	0.75	7-1/2
5	10	8	3/4	0.88	8-1/2
6	11	8	3/4	0.88	9-1/2
8	13-1/2	8	3/4	0.88	11-3/4
10	16	12	7/8	1	14-1/4
12	19	12	7/8	1	17
14	21	12	1	1.12	18-3/4
16	23-1/2	16	1	1.12	21-1/4
18	25	16	1-1/8	1.25	22-3/4
20	27-1/2	20	1-1/8	1.25	25
24	32	20	1-1/4	1.38	29-1/2

ASME/ANSI B16.5 F80 Flanges Dimensions Class-300

Nominal Pipe Size NPS (inches)	Class 300
	Diameter of Flange (inches)	No. of Bolts	Diameter of Bolts (inches)	Diameter of Bolt Holes (inches)	Bolt Circle (inches)
1/4	3-3/8	4	1/2	0.62	2-1/4
1/2	3-3/4	4	1/2	0.62	2-5/8
3/4	4-5/8	4	5/8	0.75	3-1/4
1	4-7/8	4	5/8	0.75	3-1/2
1-1/4	5-1/4	4	5/8	0.75	3-7/8
1-1/2	6-1/8	4	3/4	0.88	4-1/2
2	6-1/2	8	5/8	0.75	5
2-1/2	7-1/2	8	3/4	0.88	5-7/8
3	8-1/4	8	3/4	0.88	6-5/8
3-1/2	9	8	3/4	0.88	7-1/4
4	10	8	3/4	0.88	7-7/8
5	11	8	3/4	0.88	9-1/4
6	12-1/2	12	3/4	0.88	10-5/8
8	15	12	7/8	1	13
10	17-1/2	16	1	1.12	15-1/4
12	20-1/2	16	1-1/8	1.25	17-3/4
14	23	20	1-1/8	1.25	20-1/4
16	25-1/2	20	1-1/4	1.38	22-1/2
18	28	24	1-1/4	1.38	24-3/4
20	30-1/2	24	1-1/4	1.38	27
24	36	24	1-1/2	1.62	32

Pressure Class/ Rating

ASME/ANSI B 16.5	Lap Joint Flange, Ring Type Joint Flange, Threaded Flange, Blind Flange, High Hub Blind Flange, Socket Weld Flange, Slip on Flange, Welding Neck Flange.
PRESSURE CLASS	150, 300, 400, 600, 900, 1500, 2500
ASME/ANSI B 16.47	Blind Flange [Series A & B], Welding Neck Flange.
PRESSURE CLASS	75, 150, 300, 400, 600, 900
ASME/ANSI B 16.36	Slip on Flange, Threaded Flange, Welding Neck Flange.
PRESSURE CLASS	300, 400, 600, 900, 1500, 2500
BS 4504 SEC 3.1	Plate Flange, Welding Neck Flange, Hubbed Slip on Flange, Lapped Pipe End Flange, Loose Plate With Weld Neck Flange, Hubbed Threaded Flange, Blank Flange, Loose Plate Flange.
PRESSURE CLASS	PN 2.5 TO PN 40
BS 4504[PART 1]	Blank Flange, Loose Plate With Weld On Plate Collar, Welding Neck Flange, Plate Flange, Hubbed Slip-On Hubbed Threaded.
PRESSURE CLASS	PN 2.5 TO PN 400
BS 1560 BOSS	Blind Flange, Screwed Boss Flange, Welding Neck Flange,Slip-On Flange, Lapped Flange, Socket Welding Flange.
PRESSURE CLASS	150, 300, 400, 600, 900, 1500, 2500
BS10	Screwed Boss Flange, Plate Slip-On Flange, Slip-On Boss Flange, Blind Flange, Welding Neck Flange.
TABLE	D, E, F, H
DIN FLANGES	DIN 2527, 2632, 2635, 2673, 2566, 2655, 2631, 2627, 2634, 2576, 2636, 2629, 2633, 2573, 2656, 2638, 2637, 2642, 2641, 2628
PRESSURE CLASS	PN 6 TO PN 100